How to Clean a Tile Roof Without Breaking Tiles
How to clean a concrete or clay tile roof: what grows on tile, the best cleaners and mix strength, how to walk on tile without breaking it, the downsides of DIY, and how we soft wash tile roofs.
By Roy Bielewicz

Tile roofs last a long time, but in Florida they turn dark with algae, mildew, and lichen surprisingly fast. The safest way to clean a tile roof is a low-pressure soft wash with sodium hypochlorite (SH), done by someone who knows how to walk on tile without breaking it. In this guide, we cover what grows on tile roofs, the best cleaners for concrete and clay tile, what it takes to do it yourself, and how we clean tile roofs at Radiant Clean.

What grows on a tile roof?
The black and gray staining on most Florida tile roofs is the same algae that streaks shingle roofs, Gloeocapsa magma. On older or shaded roofs you’ll also see mildew, and lichen, which looks like crusty gray-green or orange spots. Tile has a rougher, more porous surface than shingles, so growth takes hold easily and spreads into the gaps where the tiles overlap.

How algae and lichen damage roof tiles
They hold moisture. Concrete and clay tiles are porous. A layer of algae keeps them damp long after the rain stops.
Lichen grips the surface. It anchors itself to the tile and slowly roughens and etches it.
The finish wears faster. Many concrete tiles have a colored coating. A surface that stays damp and rough loses that finish sooner.
The roof gets slick. Algae makes tile slippery, which matters for anyone who has to go up there, including roofers and inspectors.
Concrete tile vs. clay tile
Concrete tile is the most common in Tampa Bay. It’s heavier, more porous, and tends to grow more algae, but it’s a little more forgiving to walk on. Clay (terracotta) tile is less porous but more brittle, so it cracks more easily underfoot. Both clean up well with the right mix.
Why you shouldn’t pressure wash a tile roof
High pressure can crack tiles, strip the colored finish off concrete tile, and drive water up under the tiles toward the underlayment. It also takes far more time on the roof, walking back and forth with a wand. A low-pressure soft wash kills the growth so it can rinse away naturally, without any of that risk. Here’s more on why pressure washing should never be used on roofs.
The best cleaner for tile roofs
Sodium hypochlorite is what we use on most tile roofs. It kills algae, mildew, and lichen and lifts the dark staining in one application. For tile, we typically mix it to 5% to 6% and add a little more surfactant than we’d use on shingles. Solution runs off the curved tile faster, and the extra surfactant helps it cling long enough to work. On a very dirty roof, we make a second pass rather than mixing it stronger.
Sodium percarbonate (oxygen bleach) is another option. It’s gentler on plants but slower, and it struggles with heavy black growth and lichen, so it often takes more than one round. For a deeper look at how these cleaners work, see our guide to cleaning roof shingles, which covers SH, percentages, and other options in detail.

You can see how fast SH works in the photo above. The tiles on the right have just been treated, and the color is already coming back, while the tiles on the left still have a full layer of algae.
How to walk on a tile roof without breaking tiles
This is the part most people underestimate. Roof tiles are strong under rain and weight spread evenly across the roof, but a single footstep in the wrong spot can crack one. A cracked tile can let water reach the underlayment, and matching replacement tiles on an older roof isn’t always easy.

Step on the lower edge of each tile, where it overlaps the tile below. That’s where it has the most support.
Avoid the middle of a tile, where it can bridge over a gap and snap.
Stay off the hip and ridge caps whenever you can.
Start at the bottom and work your way up. Once the roof is wet, it gets slick, so you want to finish above the wet sections, not walk back down through them.
Wear soft, grippy boots made for wet surfaces, and move slowly. Algae-covered tile is slippery.
Be extra careful with clay tile, which is more brittle than concrete.
Even with training, an older roof may have tiles that are already cracked or loose. We note any broken or slipped tiles we find so you know what was there before we started.
Can you clean a tile roof yourself?
You can, with a pump sprayer and pool chlorine, but tile roofs are harder than shingle roofs for a DIY job:
It takes a lot of mix. Porous tile soaks up solution. On one very dirty tile roof in FishHawk, we used about 50 gallons of sodium hypochlorite at 12% strength, mixed down to about 6% for the application. That’s roughly 100 gallons of solution on the roof. To get the same amount of cleaning power from household-strength bleach, you’d need almost twice as much, plus dozens of trips up and down with a pump sprayer.
It takes a lot of time, refilling the sprayer, climbing down, and climbing back up in the heat.
It’s easy to break tiles if you don’t know where to step, and replacements can cost more than the cleaning.
Falls are a real risk. Wet tile and surfactant are slick, and many tile homes are two stories.
Runoff goes straight into your landscaping. Many tile homes have few or no gutters, so the solution drips off every edge. Without pre-soaking and rinsing, plants and grass can burn.
How Radiant Clean cleans tile roofs
We protect your landscaping, pre-soaking plants and roots before we start, keeping them wet while we apply the mix, and rinsing them again when we’re done. We bag any gutters and downspouts and treat the runoff with a bleach neutralizer.
We mix with a proportioner system that controls exactly how much SH and surfactant go into the solution. Our SH arrives at about 12%, and we dilute it to 5% to 6% depending on how dirty the roof is.
We apply it at low pressure with roof nozzles that reach across the tile, and we make sure the mix gets up under the bottom edge of each tile, where algae hides.
We walk the roof the right way, in non-slip boots, stepping on the overlaps and working from the bottom up.
We don’t rinse the roof. The SH keeps working as it dwells, then breaks down in the heat, and rain washes the residue away. Here’s how that worked on a cement tile roof in FishHawk.

We don’t seal or coat tile roofs after cleaning. Most tile is meant to breathe, and sealing can trap moisture. A regular soft wash every few years keeps a tile roof looking good without it.
Curious about price? Here’s our guide to roof cleaning costs in the Tampa region.
Get a free tile roof cleaning quote
If your tile roof has turned dark, we can clean it safely, without pressure and without cracking tiles. Learn more about our roof cleaning service or request a free estimate.
Ready for a radiant clean?
Get a free, no-obligation estimate for your home or business in the greater Tampa area.
Get in touch
Free Estimate
Ready to experience a cleaner home or business exterior? Contact us today for a free estimate.



